Welcome to Our Amana OEM Parts Page!
Hello Everyone! We Hope All of You Have A Happy, Healthful
& Prosperous 2009!
We Hope You Can Find the Amana Part
That You Need!
Thanks for the opportunity to do business with
you!
Be Prepared, Protect Your Family
from being Uncomfortable and cold on those Cold Winter Nights.....Buy a
spare part to have on hand. I do not want you to be caught out in the cold!
That is why I am offering you these parts at low prices!
Purchase your Amana Parts from us and Save $$$$! We ship UPS directly to your front door.
*We ship to the 50 United States & Canada.
Everything on this page is in stock and ready to ship.
You will receive a tracking number when we ship your order.
Dedicated
to Fair Business Practices and Customer Satisfaction!
We are members of
the Better Business Bureau with an A+ Rating.
Kentucky State Masters HVAC License # M01340
We have processed over 6,700 Successful PayPal Orders!
We Have Promptly Shipped Over 40,000 Orders Since 2002!
100%
Satisfaction Guaranteed!
 
 
Shop
With Confidence!
We
are Square Trade & PayPal Verified Members!
We
have VeriSign Secure Credit Card Processing and Cool Cart Secure Shopping Cart
Service! 
Need Help Troubleshooting Your Heating
& Air Conditioning Problems?
Amana
Ignitors & Furnace Troubleshooting Section:
Problem:
Your furnace will not ignite the gas to produce heat for your home. When a
furnace has a bad ignitor what I see most of the time is the following sequence
of operation:
1.
Thermostat calls for heat.
2.
Draft inducer motor starts.
3.
Pressure switch attached by a small plastic or rubber tube senses the negative
pressure
produced by the draft inducer and closes.
4.
Draft inducer runs for 30 seconds to a minute before you hear a gas hissing
sound. The
ignitor did not glow, the flame sensor (a small metal probe about
1/8" in diameter, with a
white porcelain base) does not sense the flame, so
after 8 to 10 seconds the hissing sounds
stops with no ignition of gas to heat
your home. Your furnace shuts down and goes into a
lock out condition until you
turn your power switch back off and on again.
Solution:
You probably need to purchase and install a new ignitor.
Below
we have pictures of Ignitors that many Amana furnaces have installed in them,
with an opportunity for you to purchase. I am glad we have the opportunity to do
business with you! The Internet is awesome!
Below
is a scanned picture of various Ignitor Ceramic Block Styles & Terminal
Block Styles.
Amana OEM Part #D9918202A Ignitor
Our first Amana ignitor is an OEM
ignitor part #D9918202A Ignitor.
This ignitor replaces
Norton's 201A & 271A ignitors. It also replaces the Uni-line 41-401
ignitors. The D9918202A ignitor has a ceramic block style "A" and a
terminal block style "A" The red wire lead length is 4 1/2
inches. Please see
pictures below. Please click the "Add to Cart" button below to
purchase. Thank You!
Uni-Line 41-401
Below we sell the Uni-Line Brand replacement ignitor for the Amana
OEM Part #D9918202A. Below we have pictures with an opportunity for you to
purchase.
Amana 10735003A Ignitor
Goodman, Amana Furnace Hot Surface
Ignitor Part #20165703S
This Goodman, Amana ignitor replaces part numbers: #20165703S,
#20165703
201657-03, Model 601. This ignitor is made specifically for Goodman GMS & GKS
furnaces. This ignitor replaces the ignitor in the Mini Igniter conversion kit
Part #0230K00001 that we sell above.
Below we have a picture of the ignitor
with an opportunity for you to purchase.
*For Your Information: When handling &
installing ignitors never touch the gray glass part of the ignitor. Handle &
install the ignitor using the white porcelain part of the ignitor. If you touch
the gray glass, it could shorten the life of the ignitor. Ignitors are very
fragile. If you drop it or hit it against something the ignitor will easily
break. Please be careful.
Amana
Furnace Flame Sensor
Section:
First, for those of you who might not know, "What
is a flame sensor?" A flame sensor is a safety device. When your
furnace's main burners ignite (light Up) the flame sensor picks up the heat from
the furnace's main burning and says, "YES," and sends a signal
back to the main furnace control board saying that it is OK to let the main
burner stay on. Or if the main burners do not ignite, the flame sensor
does not pick up the heat and says, "NO" to the main control board,
Shut That Gas Valve and Main Burners Down! Thank God we have safety controls
like the flame sensor. Most of the time, after
turning your furnace's power off, you may clean the flame sensors with
light sand cloth, emery cloth or steel wool. Reinstall the flame sensor and you
are back in business! Over the years flame sensors can build up a light coating
of burned-in dust and dirt. This insulates the flame sensor so that it doesn't
sense the heat of the flame well enough, so by cleaning it you have almost
restored it to its new condition. Seldom, but sometimes they do go out
completely. Below we have various Amana flame sensors with an
opportunity for you to purchase. It might be worth having a spare on hand.
Amana Furnace Flame Sensor Part #C6437502
Our
first flame sensor is an exact OEM (original Equipment Manufacturer's) flame
sensor for many Amana furnaces. The flame sensor has a part number C6437502. The
exposed metal is about 2 1/4" long, the white ceramic is 1 1/2" long,
and it screws in with one screw Below are pictures of the C6437502 flame sensor
with an opportunity for you to purchase.
Amana Flame Sensor Part #10735201
Our
next Amana Flame Sensor is Part # 10735201 This flame sensor is found on many
Amana, Janitrol & Goodman furnaces. Below we have pictures with an opportunity for you to purchase.
Amana 10735201 top
view:
Amana 10735201 End View:
Sorry, No Returns on Electrical,
Electronic Products Once they Have Been Installed.
Did
you find what you need? Below, you may use Google to search our site or the
Web:
Please
Remember Safety First
Please
read our disclaimer and safety related information below before attempting to do any
type of Heating
or Air Conditioning Repair. We do not want to see anyone get hurt or
shocked!
Thank You!
*Please always turn off all electrical
power, and discharge the capacitor/capacitors (if working around capacitors) before attempting to inspect or repair any heating & air conditioning
equipment. Check to make sure the electrical power is off with a reliable meter. I have never
been shocked by a capacitor (knock on wood) and rarely see them discharge, but
it is a good idea to discharge them before working around them. Please read
below. It tells you how to discharge a capacitor.
 
Please read the following:
How To Discharge The High Voltage
Capacitor: The capacitor is discharged
by creating a short circuit (direct connection) between the two capacitor
terminals and from each terminal to chassis ground (bare metal surface).
Please make sure that you are touching the insulated screw driver handle and not
the metal part of the screw driver before attempting this procedure.
-
Do this by touching the blade of an insulated-handled screw driver to
one terminal, then slide it toward the other terminal until it makes contact
and hold it there for a few seconds. ( Sometimes
this can result in a rather
"pop!")
Repeat the procedure to create a short between each capacitor terminal and
chassis ground.
If the capacitor has three terminals, use the same procedure to create a
short circuit between each terminal and then from each terminal to ground.
Disclaimer:
Arnold's Service Company,
Inc. assumes no liability for any incidental, consequential or other liability
from the use of this information. All risks and damages, incidental or
otherwise, arising from the use or misuse of the information contained herein
are entirely the responsibility of the user. Although careful precaution
has been taken in the preparation of this website information, we assume no
responsibility for omissions or errors.
Sorry, No Returns on Electrical,
Electronic Products Once they Have Been Installed.
Please
read, some reasons why you should feel at ease when ordering from Arnold's
Service Company, Inc.:
We
Would Love to Have Your Business!
1.
We Have Low Wholesale Prices on Heating
& Air Conditioning Service,
Supplies and Parts! Some of the lowest prices found on the Internet!
2.
We are dedicated to quick delivery of your parts and supplies with
quick UPS shipping right to your front door!
3.
We give immediate Email confirmation after you purchase and
follow-up
4.
We ship your order within 24 hours after you purchase. Most orders shipped the
same day!
5.
We Email you an UPS tracking number the day we ship.
Privacy Statement:
Please click here to see our Privacy Policy
page if you are interested.
Arnold's Service Company, Inc. is committed to protecting your privacy. Your
personal information will not be sold, rented and will be used ONLY by
Arnold's Service Company, Inc.
We promise you!
To purchase using PayPal, Credit Card, Visa, MasterCard,
Discover or American Express, please click on the
"Add to Cart" button next to each item you would like to purchase. You
will get an instant email "Notification of Purchase" when you
finish your transaction.
PayPal
It's Fast, Easy, Safe & Secure!
We Have VeriSign Secure Credit Card
Processing!
We
accept these credit cards:
We
are Square Trade Members and PayPal Verified
Shop With Confidence!
Thanks for visiting Arnold's Service
Company's Website!
Please visit our
Favorite Christian Websites page.
On this page we have a list of our
Favorite Christian Websites. This page is intended to remind you of the eternal promises that are
found in God's Holy Word and of God's never ending love for you.
I try to read from some of these websites early each morning. It helps me get
the day started out on the right track. I hope you enjoy these websites as much as I have!
God Bless you all.
Sincerely,
Steve & Barbara Arnold
11506 Seatonville Road
Louisville, KY. 40291
Thanks for all
Your Business and Support!
|
We
Sell Heating, Air Conditioning Parts & Supplies To You At Low Wholesale Prices!